EPP

The Mars Ion and Neutral Particle Analyzer (MINPA) is one of the three scientific instruments onboard the Tianwen-1 orbiter to investigate the Martian space environment. During Tianwen-1’s transfer orbit to Mars, the MINPA was switched on to measure the solar wind ions. Here, we present the first results of the MINPA observations in the solar wind. During cruise, nearly half of the MINPA ion field-of-view (FOV) was blocked by the lander capsule; thus only the solar-wind ions with azimuthal speeds pointing towards the unblocked FOV sectors could be detected. We perform a detailed comparison of the MINPA’s solar wind observations with data from Earth-based missions when MINPA reached its count-rate peak, finding a general consistency of the ion moments between them. The blocking effect due to the lander is evaluated quantitatively under varying solar-wind velocity conditions. Despite the blocking effect, the MINPA’s solar wind measurements during the transfer orbit suggest a good performance.

The main objective of the Mars Ion and Neutral Particle Analyzer (MINPA) aboard the Chinese Mars Exploration Mission (Tianwen-1) is to study the solar wind–Mars interaction by measuring the ions and energetic neutral atoms (ENAs) near Mars. The MINPA integrates ion and ENA measurements into one sensor head, sharing the same electronics box. The MINPA utilizes a standard toroidal top-hat electrostatic analyzer (ESA) followed by a time of flight (TOF) unit to provide measurement of ions with energies from 2.8 eV to 25.9 keV and ENAs from 50 eV to 3 keV with a base time resolution of 4 seconds. Highly polished silicon single crystal substrates with an Al₂O₃ film coating are used to ionize the ENAs into positive ions. These ions can then be analyzed by the ESA and TOF, to determine the energy and masses of the ENAs. The MINPA provides a 360°×90° field of view (FOV) with 22.5°×5.4° angular resolution for ion measurement, and a 360°×9.7° FOV with 22.5°×9.7° angular resolution for ENA measurement. The TOF unit combines a –15 kV acceleration high voltage with ultra-thin carbon foils to resolve H⁺, He²⁺, He⁺, O⁺, O₂⁺ and CO₂⁺ for ion measurement and to resolve H and O (≥ 16 amu group) for ENA measurement. Here we present the design principle and describe our ground calibration of the MINPA.

The Tan-Lu fault zone is a large NNE-trending fault zone in eastern China. Investigations of the structures of the fault zone and its surrounding areas have attracted much attention. In this study, we used dense-array ambient noise tomography to construct a three-dimensional shear wave velocity model of shallow crust in an area about 80km × 70km in Lujiang, Anhui Province, eastern China. For approximately one month we collected continuous ambient noise signals recorded by 90 short-period seismographs in the region, and obtained the short-period Rayleigh wave empirical Green's functions between stations by the cross-correlation method; we also extracted 0.5–8 s fundamental mode Rayleigh wave group velocity and phase velocity dispersion curves. Based on the direct surface wave tomography method, we jointly inverted the group velocity and phase velocity dispersion data of all paths and obtained the 3-D shear wave velocity structure in the depth range of 0–5 km. The results revealed important geological structural features of the study area. In the north region, the sedimentary center of the Hefei Basin — the southwestern part of the Chaohu Lake — shows a significant low-velocity anomaly to a depth of at least 5 km. The southwestern and southeastern regions of the array are the eastern margin of the Dabie orogenic belt and the intrusion area of Luzong volcanic rocks, respectively, and both show obvious high-speed anomalies; the sedimentary area within the Tan-Lu fault zone (about 10 km wide) shows low-velocity anomalies. However, the volcanic rock intrusion area in the fault zone is shown as high velocity. Our shallow crustal imaging results reflect the characteristics of different structures in the study area, especially the high-speed intrusive rocks in the Tan-Lu fault zone, which were probably partially derived from the magmatic activity of Luzong volcanic basin. From the Late Cretaceous to Early Tertiary, the Tan-Lu fault zone was in a period of extensional activity; the special stress environment and the fractured fault zone morphology provided conditions for magma in the Luzong volcanic basin to intrude into the Tan-Lu fault zone in the west. Our 3-D model can also provide important information for deep resource exploration and earthquake strong ground motion simulation.